NEWS

Contact me I can publish up to date packages of : kernel , I can share a image of ready to boot debian system (2GB image) without touching bootloader settings, this mean you can use both FirmWares

built a new PachEd kernel and managed to boot it through tftp and it just mount my partition and start the system SsH etc

Get everything at : http://rzr.online.fr/q/orion5x (then ContacT me by email )

Next job will be to create RaiD and tune BootLoader if needed (seems not)

TODO

SETUP

DEBIAN INSTALLER : TFTPBOOT

wget -p -r -l 1 http://d-i.debian.org/daily-images/armel/daily/orion5x/network-console/buffalo/lspro/
wget -c http://rzr.chez.com/www.rzr.online.fr/uri/http/d-i.debian.org/daily-images/armel/daily/orion5x/network-console/buffalo/lspro/uImage.buffalo
wget -c http://rzr.chez.com/www.rzr.online.fr/uri/http/d-i.debian.org/daily-images/armel/daily/orion5x/network-console/buffalo/lspro/initrd.buffalo

Then copy files to :

ls -l /srv/tftp/*.buffalo
-rw-r--r-- 1 root root 4754962 Nov 26 05:20 initrd.buffalo
-rw-r--r-- 1 root root 1471112 Nov 26 05:20 uImage.buffalo

Configure your host

sudo cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

iface eth0 inet static
  address 192.168.11.1
  netmask 255.255.255.0
  network 192.168.11.0
# broadcast 134.158.129.255
# gateway 134.158.128.1

http://lists.debian.org/debian-arm/2009/01/msg00053.html :

With recent firmwares on the v2 hardware, LS will only boot from TFTP if harddisk boot fails, or if instructed to do so via serial cable.

On Target :

  • unplug disks
  • opt: plug in blank mbr usb key (not needed)
  • plug eth cable to laptop eth

On LinuX HosT :

  • configure WifI
  • plug ac into nas

host:

sudo less -F /var/log/syslog
ifdown eth0 ; ifup eth0
busybox tftp -g -l /dev/stdout -r uImage.buffalo   192.168.11.1 | wc
#| 5702   32768 1471112
ping 192.168.11.150 # will give some info icmp_seq=46

nas :

  • switch off for 2 minutes (optional)
  • power off (optional)
  • observe : led green , red , blue , amber then fan and unit goes off
  • switch off (still off)
  • power on
  • press funct
  • switch on
  • observe : blink blue
  • release funct
  • press funct keep pressed
  • observe : blue green leds (red too?)
  • wait like 10 secs
  • release and press funct once
  • wait until syslog message like :
sudo less /var/log/syslog
Nov 26 14:56:51 lap in.tftpd[18710]: connect from 192.168.11.150 (192.168.11.150)
Nov 26 14:56:51 lap tftpd[18711]: tftpd: trying to get file: uImage.buffalo
Nov 26 14:56:51 lap tftpd[18711]: tftpd: serving file from /srv/tftp
Nov 26 14:56:53 lap in.tftpd[18714]: connect from 192.168.11.150 (192.168.11.150)
Nov 26 14:56:53 lap tftpd[18715]: tftpd: trying to get file: initrd.buffalo
Nov 26 14:56:53 lap tftpd[18715]: tftpd: serving file from /srv/tftp
Nov 26 14:57:04 lap kernel: [ 6627.510231] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Down
Nov 26 14:57:04 lap NetworkManager[1848]: <info> (eth0): carrier now OFF (device state 30)

Or :

 Aug 08 12:24:16 lap.lan.rzr.cloudns.org atftpd[22487]: Serving uImage.buffalo to 192.168.11.150:1556
 Aug 08 12:24:20 lap.lan.rzr.cloudns.org atftpd[22487]: Serving initrd.buffalo to 192.168.11.150:2407

Back on host :

# ifdown eth0 ; ifup eth0
ping -c 130 192.168.11.150 && ssh installer@192.168.11.150 # install

Open shell on target :

dmesg
[    0.000000] Linux version 3.1.0-1-orion5x (Debian 3.1.1-1) (ben@decadent.org.uk) (gcc version 4.6.2 (Debian 4.6.2-4) ) #1 Tue Nov 15 06:07:47 UTC 2011
[    0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
[    0.000000] Machine: Buffalo Linkstation Pro/Live
(...)
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.13 tftpboot=yes
(...)
[    0.000000] Memory: 128MB = 128MB total
(...)

@MorE: RaiD FtP

d-i : "Configure the network"

Dont select “Configure the network” but open a shell on target

On Host:

sudo grep 1 /proc/sys/net/ipv4/ip_forward || { echo 1 | tee /proc/sys/net/ipv4/ip_forward ; }
sudo iptables -t nat -A POSTROUTING -o wlan0 -j MASQUERADE # @S

On Target :

rm ~/.ssh/known_hosts ; ssh installer@192.168.11.150 # install
# open a shell
wget -O- http://www.opendns.org || {  wget -O- http://208.69.38.150/   && echo "nameserver  208.67.222.222" >> /etc/resolv.conf  ; }
#  wget: bad address 'www.opendns.org'
wget -O- http://208.69.38.150/  && wget -O- http://www.opendns.org && exit

Resume install

d-i : "Download installer components"

  • squeeze ?
# Download Installer Componants :  fdisk-udeb,mdcfg, nbd-modules-3.1.0-1-orion5x-di,  openssh-client-udeb:  parted-udeb:rescue-mode:  lowmem:

d-i : "Detect disks" , etc

On Single Disk :

UsB install seems not possible So I switch it off and plugin one spare blanked sata disk 40GB ( SP0411C SamSung ) : automatic repart create 3+1 partitions and used msdos/mbr part format (logical/extended)

parted /dev/sda -s unit b print
Model: ATA SAMSUNG SP0411C (scsi)
Disk /dev/sda: 40020664320B
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number  Start         End           Size          Type      File system     Flags
 1      1048576B      255852543B    254803968B    primary   ext2            boot
 2      255852544B    39644561407B  39388708864B  primary   ext4
 3      39645608960B  40019951615B  374342656B    extended
 5      39645609984B  40019951615B  374341632B    logical   linux-swap(v1)

On Pair of Disks

ToDo: next time I will try with my 2 SatA Drives

#todo: raid format etc

#todo: scp to hosts , check for passwd sshd etc
│                                         SCSI1 (0,0,0) (sda) - 1.0 TB ATA SAMSUNG HD103UJ                                                    │   
  │                                         >     #1  primary    2.0 GB    f  ext3          /boot                                               │   
  │                                         >     #2  primary   64.0 GB    f  ext4          /                                                   │   
  │                                         >     #5  logical  500.0 GB    f  ext4                                                              │   
  │                                         >     #6  logical  400.0 GB    f  ext4                                                              │   
  │                                         >         logical   33.2 GB       FREE SPACE                                                        │   
  │                                         >     #4  primary  999.3 MB    f  swap          swap                                                │   
  │
 
/sbin/parted /dev/sda -s unit chs  print
Model: ATA SAMSUNG HD103UJ (scsi)
Disk /dev/sda: 121601,80,62
Sector size (logical/physical): 512B/512B
BIOS cylinder,head,sector geometry: 121601,255,63.  Each cylinder is 8225kB.
Partition Table: msdos

Number  Start          End            Type      File system     Flags
 1      0,32,32        243,27,39      primary   ext3            boot
 2      243,27,40      8023,249,33    primary   ext4
 3      8024,27,1      117442,193,62  extended
 5      8024,27,3      68812,41,28    logical   ext4            raid
 6      68812,73,61    117442,193,62  logical   ext4            raid
 4      121479,187,52  121601,57,55   primary   linux-swap(v1)

In other words i set :

  • p1bootg2 : ext2 2GB (2gb in case of raw dump from rescue image and avoid overlap)
  • p2rootfsg64 : ext4 64GB (64gb for full debian system including pbuilder etc)
  • p3extended
  • p4swapg1 : 1GB (at end if needed for an other usage later, ie rescue part)
  • p5raid0g500 : 500GB (0 before in case or resizing later)
  • p6raid1g300 : 300GB
  • px : 32GB experimental tests iScsi etc

“Partition disks” is over wait a bit

cat  /proc/mdstat 
Personalities : [raid0] [raid1] 
md1 : active raid1 sda6[0] sdb6[1]
      390623096 blocks super 1.2 [2/2] [UU]
      [=====>...............]  resync = 28.7% (112349888/390623096) finish=76.9min speed=60241K/sec
      
md0 : active raid0 sda5[0] sdb5[1]
      976558080 blocks super 1.2 512k chunks
      
unused devices: <none>


 mdadm --examine --brief --scan --verbose
ARRAY /dev/md/0 level=raid0 metadata=1.2 num-devices=2 UUID=01c246d2:3e4b5720:42b9d45f:25233530 name=debian:0
   devices=/dev/sdb5,/dev/sda5
ARRAY /dev/md/1 level=raid1 metadata=1.2 num-devices=2 UUID=007ad2d9:39521238:e845aee3:b672871a name=debian:1
   devices=/dev/sdb6,/dev/sda6


cd /target/boot
mkdir -p local
cd local
wget -p http://rzr.chez.com/www.rzr.online.fr/debian/initrd.img-3.1.1lsproduo-00009-g4d27e1c.initrd.buffalo
wget -p -r -l 1 http://rzr.chez.com/www.rzr.online.fr/debian
wget http://rzr.chez.com/www.rzr.online.fr/debian/linux-image-3.1.1lsproduo-00009-g4d27e1c_3.1.1lsproduo-00009-g4d27e1c-1_armel.deb

“Configure MD devices” seems to be stuck on :

12680 root      1724 S    udpkg --configure --force-configure mdcfg
12681 root      1936 R    {mdcfg.postinst} /bin/sh /var/lib/dpkg/info/mdcfg.postinst configure
# #sh -x /var/lib/dpkg/info/mdcfg.postinst configure
# kill -s INT 11070

More

d-i : "Installing the base system"

So I log in again and Skipped previous MD steps that seem to be stuck …

It will take half an hour and ends by asking you if you want a kernel 2.6 or 3 …

I did opt for linux-image-orion5x (vmlinuz-3.1.0-1-orion5x) … then initramfs targeted

Follow other steps, package manager, “Select and install software”, tasksel ssh-server etc (default will install exim and nfs ) , it took like 1 whole hour

I skipped “Make the system bootable” to “Continue without boot loader”

You will need to boot manually with the 
/vmlinuz kernel on partition /dev/sda1 
and root=/dev/sda2 passed as a kernel argument.          │     

Backup the whole fs if you want , you'll need to MounT it 1st

tar cvf - /target/boot | ssh root@192.168.11.1 " cat - >/tmp/target-boot.tar"

~ # df -h
Filesystem                Size      Used Available Use% Mounted on
none                     12.3M     32.0K     12.2M   0% /run
tmpfs                    61.3M         0     61.3M   0% /dev
/dev/sda2                36.1G    776.3M     33.5G   2% /target
/dev/sda1               227.7M      5.1M    210.5M   2% /target/boot
/dev/sda2                36.1G    776.3M     33.5G   2% /dev/.static/dev
tmpfs                    61.3M         0     61.3M   0% /target/dev
tail var/log/installer/syslog

Nov 26 20:28:54 finish-install: info: Running /usr/lib/finish-install.d/20final-message
Nov 26 20:29:40 finish-install: info: Running /usr/lib/finish-install.d/21micro-evtd
Nov 26 20:29:40 finish-install: /usr/sbin/micro-evtd.command: 
Nov 26 20:29:40 finish-install: line 10: 
Nov 26 20:29:40 finish-install: syntax error: bad function name
Nov 26 20:29:40 finish-install: 
Nov 26 20:29:40 finish-install: info: Running /usr/lib/finish-install.d/21qcontrol
Nov 26 20:29:40 finish-install: info: Running /usr/lib/finish-install.d/30hw-detect
Nov 26 20:29:40 finish-install: info: Running /usr/lib/finish-install.d/50config-target-network
Nov 26 20:29:40 finish-install: info: Running /usr/lib/finish-install.d/55netcfg-network-manager
Nov 26 20:29:41 finish-install: info: Running /usr/lib/finish-install.d/60cleanup
Nov 26 20:29:41 finish-install: info: Running /usr/lib/finish-install.d/65partman-md
Nov 26 20:29:42 finish-install: info: Running /usr/lib/finish-install.d/90base-installer
Nov 26 20:29:42 finish-install: info: Running /usr/lib/finish-install.d/90console
Nov 26 20:29:42 finish-install: Configuring init for serial console
Nov 26 20:29:42 finish-install: info: Running /usr/lib/finish-install.d/94save-logs

cat var/log/dmesg
(Nothing has been logged yet.)

cat var/log/boot 
(Nothing has been logged yet.)

ls /target/boot

MOUNT / CHROOT

You can try to reboot now but it will fail to boot kernel, so you'll have to enter the installer again and install a custom kernel …

So let's mount and ChRoot before ReBooting

export SHELL=/bin/bash
apt-get install screen avr-evtd hddtemp
apt-get install git # ca-certificates{a} git git-man{a} less{a} libcurl3-gnutls{a} liberror-perl{a} libldap-2.4-2{a} librtmp0{a} libsasl2-2{a} libsasl2-modules{a} 
openssl{a} patch{a} rsync{a}
cat etc/network/interfaces 
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
allow-hotplug eth0
iface eth0 inet static
        address 192.168.11.150
        netmask 255.255.255.0
        network 192.168.11.0
        broadcast 192.168.11.255
        gateway 192.168.11.1
        # dns-* options are implemented by the resolvconf package, if installed
        dns-nameservers 192.168.11.1
        dns-search example.org

TODO : INSTALL KERNEL

Now install my custom kernel from : http://rzr.chez.com/www.rzr.online.fr/debian/ :

linux-headers-3.1.1lsproduo-00009-g4d27e1c_3.1.1lsproduo-00009-g4d27e1c-1_armel.deb
linux-image-3.1.1lsproduo-00009-g4d27e1c_3.1.1lsproduo-00009-g4d27e1c-1_armel.deb
linux-libc-dev_3.1.1lsproduo-00009-g4d27e1c-1_armel.deb  
cat /proc/version  ; dmesg
Linux version 3.1.1lsproduo-00009-g4d27e1c (rzr@lap) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 PREEMPT Sat Dec 3 23:43:17 CET 2011
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Buffalo Linkstation Pro Duo - Revision 2

@TaG: CrosS CompilE orion5x LsProDuo

BOOTLOADER

See UBoot page

d-i : "Finishing the installation"

Now it will reboot and send a dhcp request

WIP : reboot

then click “Finishing the installation” , UTC it will reboot on a dhcp query

If it's ok you can create a backup image to be restored later using :

time dd if=/dev/sdc | tee /dev/sdb >/dev/sda

I checked it worked, only a few warnings …

EXT3-fs (sda2): error: couldn't mount because of unsupported optional features (240)
EXT2-fs (sda2): error: couldn't mount because of unsupported optional features (240)
EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
XFS (sda5): bad magic number
XFS (sda5): SB validate failed

todo : HARDWARE

lsmod
Module                  Size  Used by
tun                    14479  2 
binfmt_misc             7265  1 
fuse                   68865  1 
evbug                   1995  0 
root@debian:~# dmesg  | grep Machine
Machine: Buffalo Linkstation Pro Duo - Revision 2

cat /proc/linkstation/gpio/fan
state: full

echo slow > /proc/linkstation/gpio/fan ; sleep 2
echo fast > /proc/linkstation/gpio/fan ; sleep 2
echo full > /proc/linkstation/gpio/fan ; sleep 2
echo slow > /proc/linkstation/gpio/fan ; sleep 2

aptitude install micro-evtd 
  
aptitude install nfs-kernel-server samba
cat /etc/exports 
#| / 192.168.11.1(rw,sync,no_root_squash)  # UnSecure
/etc/init.d/nfs-kernel-server restart
aptitude install smartmontools hddtemp
  
crontab -e
*/3 * * * * /root/local/bin/fanctrl.sh auto > /dev/null 2>&1

8acf08d01c02416fc841e820334d8905  /root/local/bin/fanctrl.sh

head  /root/local/bin/fanctrl.sh
#!/bin/sh
#
if [ $# -ne 1 ]; then
cat 2>&1 << EOF
##############################################
 fanctrl
 -------
 purpose: adjusts Kurobox fan speed based on supplied argument

 author: Mathias Weiersmueller ( matti_at_weiersmuellerdotcom )

  echo -n "\\\\" > /dev/ttyS1
  bash: echo: write error: Input/output error

https://gist.github.com/3230334

HARDWARE GPIO

  • create raid on pair of HDD
modprobe  -v gpio-fan
insmod /lib/modules/3.1.0-1-orion5x/kernel/drivers/hwmon/gpio-fan.ko 

http://lxr.free-electrons.com/source/drivers/hwmon/gpio-fan.c

https://github.com/rzr/linux/commit/0bdbeb27a04b06786f236b8d0e3e8592fcd3684d

EvtD :

apt-get install micro-evtd
Reading package lists... Done
Building dependency tree       
Reading state information... Done
The following package was automatically installed and is no longer required:
  libaio1
Use 'apt-get autoremove' to remove them.
The following NEW packages will be installed:
  micro-evtd
0 upgraded, 1 newly installed, 0 to remove and 90 not upgraded.
Need to get 31.6 kB of archives.
After this operation, 101 kB of additional disk space will be used.
Get:1 http://ftp.fr.debian.org/debian/ wheezy/main micro-evtd armel 3.4-2 [31.6 kB]
Fetched 31.6 kB in 0s (99.0 kB/s)
Selecting previously unselected package micro-evtd.
(Reading database ... 98907 files and directories currently installed.)
Unpacking micro-evtd (from .../micro-evtd_3.4-2_armel.deb) ...
Processing triggers for man-db ...
Setting up micro-evtd (3.4-2) ...
micro-evtd error: device is not supported ... failed!
invoke-rc.d: initscript micro-evtd, action "start" failed.
dpkg: error processing micro-evtd (--configure):
 subprocess installed post-installation script returned error exit status 1
configured to not write apport reports
                                      Errors were encountered while processing:
 micro-evtd
E: Sub-process /usr/bin/dpkg returned an error code (1)

@more: GpIo InitRd BooT Linux-Kernel

todo : SOFTWARE

 sudo aptitude install \
    installation-report reportbug sudo samba aptitude \
    mdadm testdisk xfsprogs  ajaxterm aria2c tmux \
    bitlbee bip smartmontools hddtemp micro-evtd  nfs-kernel-server samba 
cat /etc/network/interfaces
auto lo
iface lo inet loopback

auto eth0
allow-hotplug eth0
iface eth0 inet dhcp
 up   ip addr add 192.168.11.15/24  dev eth0 label eth0:1

Performances :

  • rsync / ssh : 1.3MB/s to RAID0 part
  • nfs-kernel-server

@more: NfS SerV SmtP IrC XmpP SsH HttpD

USB

On InstalL :

I wish I can install to UsB to test , but it fails to see it

~ # dmesg | grep sd
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.13 tftpboot=yes
dmesg | grep usb
[   12.659698] usbcore: registered new interface driver usbfs
[   12.709550] usbcore: registered new interface driver hub
[   12.794599] usbcore: registered new device driver usb
[   13.000590] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   13.007454] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   13.014699] usb usb1: Product: Marvell Orion EHCI
[   13.019399] usb usb1: Manufacturer: Linux 3.1.0-1-orion5x ehci_hcd
[   13.025608] usb usb1: SerialNumber: orion-ehci.0
[   13.270505] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[   13.277368] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   13.284623] usb usb2: Product: Marvell Orion EHCI
[   13.289331] usb usb2: Manufacturer: Linux 3.1.0-1-orion5x ehci_hcd
[   13.295541] usb usb2: SerialNumber: orion-ehci.1
[  962.752591] usbcore: registered new interface driver usb-storage
# dmseg | tail
[  962.749543] Initializing USB Mass Storage driver...
[  962.752591] usbcore: registered new interface driver usb-storage
[  962.752627] USB Mass Storage support registered.
[ 1009.920078] Btrfs loaded
[ 1010.283622] JFS: nTxBlock = 981, nTxLock = 7851
[ 1011.856089] device-mapper: uevent: version 1.0.3
[ 1011.861104] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com
cat /proc/version 
Linux version 3.1.0-1-orion5x (Debian 3.1.1-1) (ben@decadent.org.uk) (gcc version 4.6.2 (Debian 4.6.2-4) ) #1 Tue Nov 15 06:07:47 UTC 2011

Tried to hotplug one SatA disk but did not detected neither …

On Bad UsB MeM (upper slot) :

usb 2-1: new high speed USB device number 2 using orion-ehci
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high speed USB device number 3 using orion-ehci
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high speed USB device number 4 using orion-ehci
usb 2-1: device not accepting address 4, error -71
usb 2-1: new high speed USB device number 5 using orion-ehci
usb 2-1: device not accepting address 5, error -71
hub 2-0:1.0: unable to enumerate USB device on port 1

MISC : RESCUE / TFTP

Skip that , but You can even try use to use host modules through tftp

cd /var/srv
wget http://cdn.debian.net/debian/pool/main/l/linux-2.6/linux-image-3.1.0-1-orion5x_3.1.1-1_armel.deb
dpkg-deb --extract linux-image-3.1.0-1-orion5x*.deb
l="lib/modules/3.1.0-1-orion5x/kernel/fs/mbcache.ko lib/modules/3.1.0-1-orion5x/kernel/fs/jbd/jbd.ko /lib/modules/3.1.0-1-orion5x/kernel/fs/ext3/ext3.ko "
for f in $l ; do insmod $f ; done
cd /mnt
mount /dev/sda2 .
l="dev dev/pts sys proc"
for t in $l ; do mkdir -p ./$t && mount --bind /$t ./$t ; done
chroot /mnt bin/bash

export SHELL=/bin/bash
mount -t devpts devpts /dev/pts
aptitude install screen
screen 
cat /etc/network/interfaces 
#| allow-hotplug eth0
#| iface eth0 inet static
#| 	address 192.168.11.150

Error :

If used ext4 :

# mount: mounting /dev/sda2 on /mnt/ failed: Invalid argument
# [  578.613064] EXT3-fs (sda2): error: couldn't mount because of unsupported optional features (240)

f="lib/modules/3.1.0-1-orion5x/kernel/fs/ext4/ext4.ko"
# f=lib/modules/3.1.0-1-orion5x/kernel/fs/jbd2/jbd2.ko
f=lib/modules/3.1.0-1-orion5x/kernel/lib/crc16.ko
# f=lib/modules/3.1.0-1-orion5x/kernel/lib/crc-t10dif.ko
d=$(dirname $f)
mkdir -p $d
busybox tftp -g -l $f -r $f   192.168.11.1 
insmod  $f
#  [ 1528.686469] ext4: Unknown symbol crc16 (err 0)
# insmod: error inserting 'lib/modules/3.1.0-1-orion5x/kernel/lib/crc16.ko': -1 Invalid module format
# chroot: can't execute '/bin/network-console': No such file or directory

@more: InitRd RamFs RootFs

MISC : flash

sh-3.2# parted  /dev/sda -s unit b print
Model: SAMSUNG HD103UJ (scsi)
Disk /dev/sda: 1000204886016B
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number  Start        End             Size           Type      File system  Flags
 1      32256B       1028159999B     1028127744B    primary   ext3              
 2      1028160000B  6152509439B     5124349440B    primary   xfs               
 4      6152509440B  1000202273279B  994049763840B  extended                    
 5      6152541696B  7180669439B     1028127744B    logical   linux-swap        
 6      7180701696B  999190563839B   992009862144B  logical   xfs               

sh-3.2# parted  /dev/sdb -s unit b print
Model: SAMSUNG HD103UJ (scsi)
Disk /dev/sdb: 1000204886016B
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number  Start        End             Size           Type      File system  Flags
 1      32256B       1028159999B     1028127744B    primary   ext3              
 2      1028160000B  6152509439B     5124349440B    primary   xfs               
 4      6152509440B  1000202273279B  994049763840B  extended                    
 5      6152541696B  7180669439B     1028127744B    logical   linux-swap        
 6      7180701696B  999190563839B   992009862144B  logical   xfs      

@tag: TFtP ParT

MISC

irc://irc.freenode.net/linkstationwiki

MORE

armv5.txt · Last modified: 2023/02/04 20:32 by rzr
 
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
Recent changes RSS feed Donate Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki